How to use EVA Hot Melt Adhesive Film?
1. Open the packaging and place it into the hot melt adhesive machine.
The packaging is made of high quality. It is widely used for the packaging of food, medicine and daily necessities. The hot melt adhesive machine has a high degree of automation, simple operation and easy maintenance.
2. Turn on the power supply and start heating up.
Once the power is turned on, it will start warming up. When you've got hot enough juice to melt plastic, start sculpting! I like to make a shape that looks like a "U" with a long tail coming out of the top. This is because the melting plastic will drip down and make a nice edge along the bottom of your prop. The center of your "U" should be in the middle of your prop and not too close to the edges. You want to avoid dripping on yourself! Once you've melted a little bit, pull out the hot plastic and let it drip onto itself until it looks like a flat sheet of frosting (like in the photo). Let this cool all the way before moving on to step 3.
3. The temperature can be adjusted according to the user's product, generally it is 160-200 degrees.
There are two types of heat shrink film machines. The high-pressure hot air heat shrink film machine produces a large amount of hot air from the hot air blower. It is sent to the enclosed heating chamber through the pipeline to make the room temperature reach 150-200 degrees, and then the box enters the heating chamber to be heated and shrunk. When the heat shrink film machine is in operation, it is necessary to pay attention to whether the temperature inside the heating chamber is normal. If there is a problem, you should stop it immediately and check it carefully. Generally speaking, this type of equipment does not have much trouble because of its simple structure. There are many kinds of electric heat shrink film machines. Some use electric heating tubes for heating, and some use steam as a medium for heating and shrinking. When using an electric heat shrink film machine, pay attention to whether there is any abnormality in the operation of the electric heating tube or whether there is any problem with the steam pressure during use. If there is an abnormal phenomenon, please stop it immediately for inspection and maintenance to avoid damage caused by abnormal operation.
4. After the adhesive film melts, apply the right amount of adhesive evenly to your product.
Now that your adhesive film has melted, it's time to apply it to your product. Make sure to apply the adhesive in even, thin layers. If you use too much or apply it unevenly, you may find that the adhesive is difficult to remove from where it doesn't belong, and you may damage your product in the process. If you don't have enough adhesive on a particular area, it won't be able to bond properly with its surface. Don't panic if you accidentally over- or under-apply the adhesive; not all hope is lost! Try using a paintbrush dipped in hot water to dab areas where there's too much of the adhesive until they're no longer sticky. You can also add more glue to areas where there isn't enough. Try experimenting with different combinations of brushes and liquids (such as oil or alcohol) until you figure out what works best for removing excessive glue on your particular products.https://sinohotmelt.com/
1. Open the packaging and place it into the hot melt adhesive machine.
The packaging is made of high quality. It is widely used for the packaging of food, medicine and daily necessities. The hot melt adhesive machine has a high degree of automation, simple operation and easy maintenance.
2. Turn on the power supply and start heating up.
Once the power is turned on, it will start warming up. When you've got hot enough juice to melt plastic, start sculpting! I like to make a shape that looks like a "U" with a long tail coming out of the top. This is because the melting plastic will drip down and make a nice edge along the bottom of your prop. The center of your "U" should be in the middle of your prop and not too close to the edges. You want to avoid dripping on yourself! Once you've melted a little bit, pull out the hot plastic and let it drip onto itself until it looks like a flat sheet of frosting (like in the photo). Let this cool all the way before moving on to step 3.
3. The temperature can be adjusted according to the user's product, generally it is 160-200 degrees.
There are two types of heat shrink film machines. The high-pressure hot air heat shrink film machine produces a large amount of hot air from the hot air blower. It is sent to the enclosed heating chamber through the pipeline to make the room temperature reach 150-200 degrees, and then the box enters the heating chamber to be heated and shrunk. When the heat shrink film machine is in operation, it is necessary to pay attention to whether the temperature inside the heating chamber is normal. If there is a problem, you should stop it immediately and check it carefully. Generally speaking, this type of equipment does not have much trouble because of its simple structure. There are many kinds of electric heat shrink film machines. Some use electric heating tubes for heating, and some use steam as a medium for heating and shrinking. When using an electric heat shrink film machine, pay attention to whether there is any abnormality in the operation of the electric heating tube or whether there is any problem with the steam pressure during use. If there is an abnormal phenomenon, please stop it immediately for inspection and maintenance to avoid damage caused by abnormal operation.
4. After the adhesive film melts, apply the right amount of adhesive evenly to your product.
Now that your adhesive film has melted, it's time to apply it to your product. Make sure to apply the adhesive in even, thin layers. If you use too much or apply it unevenly, you may find that the adhesive is difficult to remove from where it doesn't belong, and you may damage your product in the process. If you don't have enough adhesive on a particular area, it won't be able to bond properly with its surface. Don't panic if you accidentally over- or under-apply the adhesive; not all hope is lost! Try using a paintbrush dipped in hot water to dab areas where there's too much of the adhesive until they're no longer sticky. You can also add more glue to areas where there isn't enough. Try experimenting with different combinations of brushes and liquids (such as oil or alcohol) until you figure out what works best for removing excessive glue on your particular products.https://sinohotmelt.com/
How to use EVA Hot Melt Adhesive Film?
1. Open the packaging and place it into the hot melt adhesive machine.
The packaging is made of high quality. It is widely used for the packaging of food, medicine and daily necessities. The hot melt adhesive machine has a high degree of automation, simple operation and easy maintenance.
2. Turn on the power supply and start heating up.
Once the power is turned on, it will start warming up. When you've got hot enough juice to melt plastic, start sculpting! I like to make a shape that looks like a "U" with a long tail coming out of the top. This is because the melting plastic will drip down and make a nice edge along the bottom of your prop. The center of your "U" should be in the middle of your prop and not too close to the edges. You want to avoid dripping on yourself! Once you've melted a little bit, pull out the hot plastic and let it drip onto itself until it looks like a flat sheet of frosting (like in the photo). Let this cool all the way before moving on to step 3.
3. The temperature can be adjusted according to the user's product, generally it is 160-200 degrees.
There are two types of heat shrink film machines. The high-pressure hot air heat shrink film machine produces a large amount of hot air from the hot air blower. It is sent to the enclosed heating chamber through the pipeline to make the room temperature reach 150-200 degrees, and then the box enters the heating chamber to be heated and shrunk. When the heat shrink film machine is in operation, it is necessary to pay attention to whether the temperature inside the heating chamber is normal. If there is a problem, you should stop it immediately and check it carefully. Generally speaking, this type of equipment does not have much trouble because of its simple structure. There are many kinds of electric heat shrink film machines. Some use electric heating tubes for heating, and some use steam as a medium for heating and shrinking. When using an electric heat shrink film machine, pay attention to whether there is any abnormality in the operation of the electric heating tube or whether there is any problem with the steam pressure during use. If there is an abnormal phenomenon, please stop it immediately for inspection and maintenance to avoid damage caused by abnormal operation.
4. After the adhesive film melts, apply the right amount of adhesive evenly to your product.
Now that your adhesive film has melted, it's time to apply it to your product. Make sure to apply the adhesive in even, thin layers. If you use too much or apply it unevenly, you may find that the adhesive is difficult to remove from where it doesn't belong, and you may damage your product in the process. If you don't have enough adhesive on a particular area, it won't be able to bond properly with its surface. Don't panic if you accidentally over- or under-apply the adhesive; not all hope is lost! Try using a paintbrush dipped in hot water to dab areas where there's too much of the adhesive until they're no longer sticky. You can also add more glue to areas where there isn't enough. Try experimenting with different combinations of brushes and liquids (such as oil or alcohol) until you figure out what works best for removing excessive glue on your particular products.https://sinohotmelt.com/
0 Commenti
0 condivisioni
3119 Views
English
French
Spanish
Portuguese
Deutsch
Turkish
Dutch
Russian
Romaian
Portuguese (Brazil)
Greek
urdu